FINISHING END CAP #94 (BLACK) – 1 UNIT

Name: FINISHING END CAP #94 (BLACK) – 1 UNIT
Brand: LEDCO
SKU: LCENDCAP-STAND-94-BK
Price: 17.97 CAD
Availability: InStock

SKU: LCENDCAP-STAND-94-BK

Brand: LEDCO

Those two little open ends are what separate a clean, professional LED strip installation from an unfinished one — and that is exactly what this finishing end cap takes care of. Sold as a single unit in black, this model #94 cap is the finishing piece that closes off the extremity of an aluminum LED channel, also called an LED profile, LED extrusion or strip light housing. People search for it as an LED channel end cap, an LED strip light end cap or simply a profile cap, and it always does the same job: it seals the opening, hides the cut edge of the aluminum and the end of the tape, and keeps dust and curious fingers away from the diodes. Whether you are running under-cabinet lighting in a kitchen, cove lighting in a living room, shelf and display lighting in a boutique or linear accents in an office corridor, this is the small accessory that makes the whole run look intentional.

The finish is black, so it blends with black-anodized profiles and disappears against dark ceilings, dark millwork and modern matte-black hardware instead of creating a bright spot at the end of the run. It is a #94 profile-specific cap: the shape is matched to that extrusion family, which means it slides into place snugly and stays put without hardware showing. You get 1 unit per item, so you order exactly what your project needs — two per finished run, one per run when the other end butts into a wall, a corner or a connector, and a few extras for the inevitable cut-and-fit adjustments on site. No wiring, no tools required in most cases: position it on the end of the profile and press it home.

Contractors, cabinetmakers and homeowners across Canada use these caps everywhere strip lighting goes: kitchen and bathroom vanities, closets and pantries, stair nosings, basement ceilings, retail display cases, reception desks and restaurant bars. Because the fit is profile-dependent, pick the cap number that matches your channel — and if you are working with other extrusions, look at the Finishing end cap #11 (no hole), the Finishing end cap #12 (with hole), the Finishing end cap #13 or the Finishing end cap #15. Add SKU LCENDCAP-STAND-94-BK to your order and finish your LED runs the right way.

Compatible with
Works with:
Channel / profile: LCPROF-94-16FT-BK, LCPROF-94-8FT-BK

What this accessory is
This is a finishing end cap for LED channel, model #94, in a black finish, sold as 1 unit. It is the closing piece installed at the extremity of an aluminum LED profile once the strip is mounted and the diffuser lens is in place. Its role is simple but important: it frames the cut end of the extrusion, conceals the end of the LED strip and its solder points, and gives the run a finished, factory-made appearance instead of an exposed opening. On a jobsite, it is also the piece that makes an on-site cut look deliberate rather than improvised.

Fit and compatibility
End caps are profile-specific: each number corresponds to a channel cross-section, and a cap will only seat properly on its matching extrusion. This one is the #94 version, so use it with the #94 channel family. The black colour is chosen to pair with dark-finish profiles and dark surroundings — black ceilings, walnut or charcoal millwork, matte-black trims and hardware — so the eye follows the line of light instead of stopping at a contrasting end. If your project mixes several extrusion sizes, simply match each run to its own cap number rather than forcing a cap that was not designed for it.

Technical specifications
SKU: LCENDCAP-STAND-94-BK
Product: Finishing end cap #94
Colour / finish: Black
Quantity: 1 unit
Type: End cap for LED channel / LED profile
Use: Residential and commercial LED strip installations

Installation tips
Plan on two caps per finished run, or one when the opposite end disappears into a wall, a corner, a cabinet return or a connection point. Install the strip and the diffuser first, verify that the channel is cut square — a clean cut is what makes a cap sit flush — then seat the cap on the end and press it into place. Where the power lead or a jumper exits the extrusion, that end usually calls for a cap version with a hole while the closed end takes a solid cap; order accordingly so the wire exits cleanly and nothing is pinched. It is always wise to keep a couple of spares on hand: caps are small, and jobsite adjustments happen.

Where it is used
You will find these caps on every kind of linear lighting project: under-cabinet lighting in kitchens, vanity and mirror lighting in bathrooms, cove and ceiling perimeter lighting in living rooms and condos, stair and hallway accents, closet and pantry strips, plus commercial work like retail shelving, display cases, reception counters, restaurant bars, office workstations and showroom millwork. Need caps for other extrusions in the same order? See the Finishing end cap #11 (with hole), the Finishing end cap #12 (no hole), the Finishing end cap #14 (no hole) and the Finishing end cap #14 (with hole) to complete every run in your project.