FINISHING END CAP #11 (WITH HOLE) – 1 UNIT

Name: FINISHING END CAP #11 (WITH HOLE) – 1 UNIT
Brand: LEDCO
SKU: LCENDCAP-STAND-11-H
Price: 3.97 CAD
Availability: InStock

SKU: LCENDCAP-STAND-11-H

Brand: LEDCO

Every clean LED strip installation ends with one small detail, and this is it. The finishing end cap #11 (with hole) is the little closing piece that caps off an aluminum LED profile — also called an LED channel, LED extrusion or strip light housing — and turns a raw cut edge into a finished, intentional line. Sold as 1 unit under SKU LCENDCAP-STAND-11-H, this version comes with a pre-made hole so the supply cable or the connector lead slips out discreetly instead of fighting its way past a solid cap. It's one of those LED channel end caps that nobody notices when it's there and everybody notices when it's missing.

The cap is shaped to match a standard profile style, so it slides into the open end of the channel for a snug, flush fit with no gap to collect dust. Because it is style-specific, always match the cap number to the profile you are actually using — a #11 cap goes on a #11 channel. Use the version with the hole at the feed end of the run, where the wire enters, and close the opposite end with the solid Finishing end cap #11 (no hole) for a completely sealed look. Installation is quick: cut and position your channel first, feed the wire through the cap, then press the cap into place. A drop of adhesive on the inside edge keeps it put in high-traffic zones or on overhead runs, while still letting you pop it off later for service.

This is the finishing touch for under-cabinet lighting, cove and ceiling details, display cases, signage, reception desks, staircases and workshop task lighting — surface-mounted, recessed or suspended. Kitchen renovations, retail counters, restaurant bars, garage benches and basement rec rooms across Canada all benefit from the same thing: an LED strip light end cap that hides the cut aluminum and keeps the wire tidy. Grab one per open end, add a few spares to the job box, and finish your channel runs the way a pro would.

What this end cap is for
An aluminum channel protects your LED tape, spreads the light through the lens and gets rid of that "bare strip stuck to the wall" look. But a cut extrusion always leaves two open ends, and open ends show the raw aluminum, the lens edge and, worse, the wire hanging out. This finishing end cap #11 with hole closes one of those ends while giving the supply cable a clean exit point. Pair it with a solid cap at the far end and the whole run reads as one continuous, deliberate line of light instead of an unfinished DIY project.

Fit and compatibility
End caps are profile-specific, not universal. This one is made for the standard #11 profile shape and slides into the open end of that channel for a snug, flush fit. Before ordering, confirm the number stamped on or listed with your LED extrusion — matching the cap to the channel is the whole game. For the same profile, the closing piece without an opening is the Finishing end cap #11 (no hole); if your project uses a different standard profile, look at the Finishing end cap #12 (no hole). Working with flexible neon rope instead of rigid channel? Then you want the neon family: Flex neon endcap 3x6 (with hole) or Flex neon endcap 6x6 (with hole), each with a matching no-hole version to close the far end.

Installation, step by step
Measure and cut your channel to length first, then dry-fit it in place. Feed the strip's lead wire or the connector through the hole in the cap before you seat anything — doing it in the other order means pulling the cap back off. Press the cap squarely into the open end until it sits flush with the aluminum face. For overhead runs, ladders, closet interiors, shop benches or anywhere hands and brooms go by, add a small drop of adhesive on the inside edge; it holds firm but still lets you remove the cap later if you ever need to re-pull a wire or swap a driver lead. Keep the cable exit facing the wall or the back of the cabinet so the wire disappears from sight lines.

Where it earns its keep
Under kitchen cabinets, where the cap hides the cut edge right at eye level from the counter. In cove and tray ceilings, where the run has to look machine-made. In retail display cases and jewellery showcases, in illuminated signage, along reception desks and bar fronts, on stair nosings and in workshop task lighting. Contractors like them because they close a run in seconds; homeowners like them because the finished job stops looking homemade. Residential or light-commercial, surface-mounted, recessed into drywall or suspended on cable, the principle is the same.

Ordering and documentation
This listing, SKU LCENDCAP-STAND-11-H, is for 1 unit, so count one cap per open end and order accordingly — most installers keep a couple of spares on hand, since these are the first small parts to disappear on a job site. No additional spec sheet or IES file is published for this accessory; selection is based on matching the #11 profile style. If you are unsure which profile you have, compare the cap's shape to the end of your channel before installing, and pick the with-hole version for the feed side and the no-hole version for the closed side.