FINISHING END CAP #14 (WITH HOLE) – 1 UNIT

Name: FINISHING END CAP #14 (WITH HOLE) – 1 UNIT
Brand: LEDCO
SKU: LCENDCAP-STAND-14-H
Price: 4.97 CAD
Availability: InStock

SKU: LCENDCAP-STAND-14-H

Brand: LEDCO

An LED channel run is only as clean as its ends — and this is the little piece that makes the whole thing look built-in. The FINISHING END CAP #14 (WITH HOLE) is a profile-specific end cap sold as 1 unit, designed to close off the open end of an aluminum extrusion once your LED strip and diffuser are in place. People search for it as an LED channel end cap, an LED strip light end cap, an aluminum profile cap or simply a channel plug — same part, same job: hide the raw cut edge, keep dust out of the channel, and give the run a finished, deliberate look instead of a gaping aluminum mouth.

This is the hole version, which means it is made for the power-entry side of your run. The opening lets the supply wire or the connector pass through without pinching the lead or leaving an ugly gap around it, so the driver feed stays tidy and the cap still sits flush against the extrusion. It is shaped for the #14 profile family, so the fit is snug and holds with a simple friction press — no tools, no hardware, no drilling. Pair it with a matching solid cap at the opposite end for a fully closed run, or use two hole caps when you are feeding a continuous run from both directions. The SKU is LCENDCAP-STAND-14-H, and since it ships as a single unit, you order exactly the number of ends your project actually has.

This little accessory earns its keep in cove lighting, under-cabinet strips, stair nosings, closet and pantry runs, display cases, retail shelving and reception desks — anywhere an LED channel is visible at eye level. It suits both residential renovations and light-commercial fit-outs in Canadian homes, shops and offices, where an unfinished channel end is the one detail clients always notice. A quick tip from the field: cut and test-fit your channel first, thread the wire through the cap before pressing it home, and leave a little slack in the lead. Match the cap to your extrusion family and finish the job properly — add this end cap to your channel order and your run will look like it was always meant to be there.

Compatible with
Works with:
Channel / profile: LCPROF-14-16FT, LCPROF-14-8FT

What it is and what it does
The FINISHING END CAP #14 (WITH HOLE) is a small but essential LED channel accessory: a finishing cap that seals the open end of an aluminum extrusion after the LED strip and the diffuser have been installed. Left open, a channel shows its cut edge, collects dust, and lets the wire flop out of the profile. Capped, the same run reads as an integrated, architectural line of light. This version is drilled for the power-entry side, so the supply wire or a connector exits cleanly through the cap instead of squeezing past the diffuser or forcing you to notch the extrusion.

Fit and compatibility
End caps are profile-specific — the cap must match the shape and size of the extrusion family it closes. This one is the #14 standard profile cap, and it is not interchangeable with other profile numbers, so always match the cap to the channel you are actually installing. Across the accessory range you will find caps for surface-mount, recessed and corner channels, with and without a hole. For a typical single-feed run you want one hole cap at the driver end and one solid cap at the far end; for a continuous run fed from both directions, use two hole caps. If you are working with a different profile, the Finishing end cap #11 (with hole) and the Finishing end cap #11 (no hole) cover the #11 family, while flexible neon installations use dedicated caps such as the Flex neon endcap 6x6 (with hole) and the Flex neon endcap 3x6 (without hole).

Installation, step by step
Cut your channel to length and test-fit it in place before you commit to anything. Install the LED strip, seat the diffuser, then run the wire through the cap before pressing the cap home — threading afterward is fiddly and risks scraping the conductor insulation. A light, even press is usually enough for a solid friction fit. For ceiling coves, mobile display carts, shop fixtures or anywhere the cap could be bumped or handled, a small dab of clear adhesive keeps it permanently in place without showing. Leave a bit of slack in the lead so the cap seats flush against the aluminum rather than being pulled off by the cable. Since the item is sold as 1 unit, count your open ends — including breaks at corners and expansion gaps — before ordering.

Technical specifications
SKU: LCENDCAP-STAND-14-H
Type: Finishing end cap, standard profile #14
Version: With hole (power-entry / wire exit)
Quantity: 1 unit
Mounting: Friction fit into the channel end
Category: End caps, lenses and accessories

Where it shines and documentation
This cap belongs on every visible channel end in under-cabinet kitchen lighting, cove and tray ceilings, stairwells, bookcases, walk-in closets, garage workbenches and basement renovations, and just as much in light-commercial work: retail display cases, jewellery counters, bar backs, salon mirrors, reception desks and office feature walls. Contractors across Canada keep a handful of each profile in the van precisely because a missing end cap is the one detail that holds up a final walkthrough. A technical PDF is available in the Documentation tab of this page for reference before you order, and pairing this hole cap with a matching solid cap gives you a complete, dust-resistant, professionally finished LED strip channel run from one end to the other.

Technical Files