ENDCAP (1X) #90 FINISHING (STANDARD) – (WITHOUT HOLE) BLACK

Name: ENDCAP (1X) #90 FINISHING (STANDARD) – (WITHOUT HOLE) BLACK
Brand: LEDCO
SKU: LCENDCAP-STAND-90-BK
Price: 5.97 CAD
Availability: InStock

SKU: LCENDCAP-STAND-90-BK

Brand: LEDCO

Small part, big difference: this is the piece that turns a raw aluminum extrusion into a finished light line. The #90 finishing end cap in black is the closed version — no cable opening — designed to seal the open end of a LED channel so the profile, the diffuser lens and the LED tape inside are no longer left exposed. If you have been searching for LED channel end caps or LED strip light end caps, this is exactly that: one single cap (1X), shaped for the #90 profile, in a black finish that disappears against dark extrusions and matte surfaces. Use it at the far end of a run, where nothing needs to pass through, and keep the wiring exit for the driver side of your layout.

Sold as a single unit (1X), this cap is the standard, without-hole version of the #90 series, which means it fully closes the channel instead of leaving a notch for a cable. Because it is shaped to match the profile it belongs to, it sits flush against the extrusion and the diffuser for a tidy, continuous edge — no gap, no visible lens end, no dust or lint sneaking into the tape. The black finish blends with common dark aluminum LED profiles and is an easy match when you want the hardware to stay invisible and let the light do the talking. Its durable construction holds up in busy kitchens, workshops and commercial rooms where profiles get bumped, wiped and handled. It works the same way in surface-mount, recessed and suspended installations, so one part covers most of your job. SKU: LCENDCAP-STAND-90-BK.

This end cap belongs in every project where a ruban LED lives inside an extrusion: under-cabinet lighting in a kitchen, cove and ceiling coffers, closets and pantries, stair nosings, retail shelving, reception desks, office linear runs, garage and workshop benches. It fits the #90 standard profile family and completes the same style of installation as our other finishing caps, including Finishing end cap #11 (no hole) and, when you need a cable exit at the feed end, Finishing end cap #11 (with hole). Install tip: cut and clean your channel first, insert the tape and diffuser, then press the cap into place. Order a few spares while you are at it — future service calls go much faster when the right cap is already in the toolbox.

Compatible with
Works with:
Channel / profile: LCPROF-90-16FT-BK-LENS-FROS, LCPROF-90-16FT-BK-LENS-OPAQ, LCPROF-90-8FT-BK, LCPROF-90-8FT-BK-LENS-FROS, LCPROF-90-8FT-BK-LENS-OPAQ

What this part is
This is a single (1X) finishing end cap for the #90 standard aluminum profile, supplied in a black finish and in the closed, without-hole configuration. Its only job is to close the cut end of an extrusion cleanly, and it does that job better than tape, filler or nothing at all. Without a cap, the aluminum edge, the ends of the diffuser lens and the LED tape stay visible from every angle — the installation reads as unfinished and stays open to dust, lint and accidental contact with the strip. With it, the run ends in a crisp line.

Fit and finish
The cap is shaped to match the profile it belongs to, so it seats flush against both the channel walls and the diffuser lens, leaving no step or shadow at the end of the run. Because it is the version without a cable opening, it forms a fully closed end — the right choice at the last extrusion of a continuous line, at the end of an under-cabinet section, or anywhere a return of light would otherwise spill out of the profile. The black finish is the discreet option: against dark or black anodized LED channels, black millwork and matte ceilings, the hardware simply vanishes.

Technical specifications
SKU: LCENDCAP-STAND-90-BK
Type: finishing end cap, standard
Profile series: #90
Configuration: without hole (closed, no cable opening)
Finish: black
Quantity: 1 unit (1X)
Compatible mounting styles: surface-mount, recessed, suspended

Installation and layout
Work in the right order and the result is clean every time: cut the channel to length, file and clean the cut, insert the LED strip and then the diffuser, and finally press the end cap into place. Plan the run before you cut — the closed cap goes at the far end, while the opening you need for the wiring stays on the driver side, so the low-voltage feed and the connection point land where you want them and not in the middle of a finished surface. If the profile will be handled often, a dab of adhesive secures the cap permanently; if you expect to reopen the channel for service, leave it as a friction fit. Keeping a couple of spare caps in the van or the drawer means a damaged end never holds up a whole job.

Where it shines and what it works with
Kitchens with under-cabinet and toe-kick lighting, cove lighting in living rooms and hallways, bookcases and display shelving, stair and corridor runs, walk-in closets, garage workbenches, workshops, retail gondolas, reception desks and office linear lighting — every one of those installations ends somewhere, and that end deserves a cap. This part serves the #90 standard profile family; for other profiles and other configurations, see the matching accessories such as Finishing end cap #11 (no hole), Finishing end cap #11 (with hole), and for flexible neon-style runs, Flex neon end cap 3x6 (without hole) or Flex neon end cap 6x6 (without hole). Note that end caps are profile-specific: always match the cap to the extrusion series you are using, and count one cap per open end when you build your parts list.