FLEX NEON ENDCAP 3X6 - (WITHOUT HOLE)

Name: FLEX NEON ENDCAP 3X6 - (WITHOUT HOLE)
Brand: LEDCO
SKU: LCENDCAP-FLX-3X6
Price: 3.97 CAD
Availability: InStock

SKU: LCENDCAP-FLX-3X6

Brand: LEDCO

Every run of LED neon flex has to stop somewhere, and that cut end deserves better than exposed silicone and a bead of glue. This flex neon end cap in the 3X6 profile size slips over the terminated end of your flexible LED neon rope light and closes it off cleanly, so the finished job looks like it was made that way from the start. It is the solid version, without a hole — the one you use at the far end of a run, where no power lead, no wire and no connector needs to exit the body. Shoppers look for it as a neon flex endcap, a neon strip end plug, a bouchon or simply "the little cap at the end of the LED neon"; whatever you call it, this is the piece that turns a raw cut into a finished edge.

This is a passive accessory, which is the beauty of it: no wiring, no polarity to respect, no dimmer compatibility to check, nothing to fail electrically. It is shaped to match the profile of common 3X6 neon flex rope so it sits flush against the silicone for a tidy, uniform appearance instead of a lumpy blob of sealant. Sold as one unit under SKU LCENDCAP-FLX-3X6, it is the kind of small part you want in quantity — most projects need one at the end of every cut section, and coming up one cap short at the end of an install is nobody's idea of a good day. Pair it with the hole version on the feed side and your run is sealed at both ends.

Where does it earn its keep? Cove lighting and ceiling coffers, LED sign and channel-letter work, under-cabinet accents, stair nosings, bar fronts, reception desks, garage and basement perimeter lighting — anywhere in a Canadian home or business where a neat, professional finish is expected and inspected. Contractors building signage or architectural coves will run through these fast. Add a few to your order, keep spares in the van, and finish every run properly the first time.

Compatible with
Works with:
LED strip: LCLS24VFLX-3X6-9.6W-27K, LCLS24VFLX-3X6-9.6W-27K-30M, LCLS24VFLX-3X6-9.6W-30K, LCLS24VFLX-3X6-9.6W-40K, LCLS24VFLX-3X6-9.6W-40K-30M

What this part is
This is the solid finishing end cap for 3X6 flexible LED neon, supplied as a single unit. It closes the terminated end of a cut run of neon flex rope, hiding the exposed silicone and the LED board edge behind a clean, matched profile. Because it has no hole, it is meant for the "dead" end of the run — the end opposite the power feed. If your cap needs to pass a power lead or a connector through it, that is a different part, and you will find it as the Flex neon endcap 3x6 with hole.

Build and fit
The cap is moulded to match the cross-section of common 3X6 neon flex profile, so it slides over the end and seats flush against the body rather than standing proud. That flush fit matters more than people expect: on a lit cove or a sign return, a mismatched cap casts a shadow line or leaves a gap that collects dust. Check your rope's profile dimensions before ordering — neon flex comes in several sections, and a 6x6 body needs the Flex neon endcap 6x6 without hole instead. Side-emitting and top-emitting profiles have their own shapes too, covered by the Flex neon endcap side view without hole and the Flex neon endcap top view without hole.

Installation, step by step
Cut your LED neon flex only at the marked cutting points — cutting between them kills the segment. Wipe the cut end clean and let it dry completely; silicone will not bond to dust, oil or moisture. Apply a bead of compatible silicone adhesive inside the cap, then press it firmly onto the end so the adhesive squeezes out evenly around the perimeter. Wipe the excess, then let it cure fully before energizing the run or exposing it to humidity. For damp locations, exterior soffits, signage or anywhere splash is possible, make sure the seal is continuous all the way around the edge — a single gap is all water needs.

Electrical notes
There is nothing electrical here, and that is the point. No polarity, no voltage rating to match, no impact on your driver sizing, no effect on dimming behaviour. The cap does not carry current and does not change the performance of the neon flex it closes. Your driver, controller and dimming choices are dictated entirely by the rope itself, not by this accessory.

Where it gets used
Think of every place a run of neon flex terminates in plain sight: the return of a channel letter or a backlit logo, the end of a cove in a condo living room, the last few inches under a kitchen upper cabinet, a stair nosing on a staircase, the underside of a bar top or a reception desk, a perimeter line in a garage or a home gym. In each of those, the cap is the difference between "looks custom" and "looks unfinished." Keep a handful on hand: most installs need one per cut section, and running short mid-job means either an ugly improvised seal or a second trip. Order SKU LCENDCAP-FLX-3X6 in the quantity your run count calls for. No documents are listed for this accessory — if you need to confirm the profile match, measure the cross-section of your neon flex before ordering.