FLEX NEON ENDCAP - TOP VIEW - (WITHOUT HOLE)

Name: FLEX NEON ENDCAP - TOP VIEW - (WITHOUT HOLE)
Brand: LEDCO
SKU: LCENDCAP-FLX-TV-NH
Price: 3.97 CAD
Availability: InStock

SKU: LCENDCAP-FLX-TV-NH

Brand: LEDCO

Finish your LED neon flex run the right way — with a clean, sealed edge instead of a raw cut face. This is the top-view closed end cap (SKU LCENDCAP-FLX-TV-NH), a small but essential accessory for top-view neon flex, the silicone flexible LED neon rope light that emits through the upper face of the extrusion. People look for it under a lot of names — end cap, embout, neon flex cap, neon sign end plug — but the job is always the same: cap the dead end of the run, the side opposite the power feed, and keep the finished look tidy. Because it has no cable hole, it's the piece you want wherever the light stops and nothing has to exit.

An open end is an invitation to dust, debris and humidity reaching the internal LED board, and it lets raw light escape from the cut face, which shows up as a bright spot at the end of an otherwise even glow. A properly installed closed cap keeps the neon flex sealed, supports the wet-location or damp-location rating of the flex it is paired with, and helps preserve consistent output over the life of the run. One detail matters more than any other: the cap profile must match your flex profile. Silicone LED neon comes in several sizes and shapes, so measure your extrusion before ordering — a top-view cap belongs on a top-view profile, and the wrong shape will never seal properly.

Cove lighting and ceiling details, under-cabinet runs, channel letters and LED neon signs, handrails, retail displays and architectural outlines — anywhere a terminated edge is part of the finished look, this cap earns its place. Canadian installers know how quickly basements, garages and exterior soffits punish an unsealed end, which is why cabinet shops, sign makers and renovators keep a handful on the truck. If your run uses a side-emitting profile instead, reach for the flex neon endcap side view without hole, and for squared profiles see the flex neon endcap 3x6 without hole or the flex neon endcap 6x6 without hole. Match your profile, seal it once, and forget about it.

Compatible with
Works with:
LED strip: LCLS24VFLX-TV-14W-27K, LCLS24VFLX-TV-14W-27K-30M, LCLS24VFLX-TV-14W-40K, LCLS24VFLX-TV-14W-40K-30M

What this end cap is
This is a closed finishing end cap designed for top-view neon flex — the silicone LED neon flex profiles that emit light through the upper face of the extrusion rather than the side. It carries no cable hole, which makes it the terminating piece: it goes on the dead end of the run, the opposite side from the power-feed connection. One cap covers one end, so count your runs before you order. Because silicone neon is produced in several sizes and shapes, matching the cap profile to your flex profile is not optional; a cap made for another profile will not sit flush, will not seal, and will eventually let the run down.

Why sealing the end matters
An open end leaves the internal LED board exposed to dust, debris and humidity — the three things that shorten the life of a flexible LED neon rope light. A properly sealed cap supports the wet-location or damp-location rating of the flex it is paired with and helps preserve consistent light output over the years. It also blocks light leakage from the cut face, so the glow stays even from the first millimetre to the last instead of ending in a hot spot. On signage and cove work, where the eye follows the line of light, that even termination is the difference between a professional install and an obviously homemade one.

Installation, step by step
Cut the neon flex only at the marked cut points — cutting anywhere else severs the circuit and ruins the segment. Wipe the freshly cut end clean and make sure it is completely dry. Apply a bead of compatible silicone adhesive or sealant inside the cap, then press the cap firmly onto the flex so the adhesive spreads across the full face. Let the adhesive cure fully before powering the run up or exposing it to moisture; rushing this step is the most common reason a "sealed" end later fogs or fails. Keep the power-feed side of the run at the accessible end so future service means unplugging rather than dismantling.

Where it gets used
Cove and ceiling details in living rooms and hotel lobbies, under-cabinet and toe-kick runs in kitchens, channel letters and storefront LED neon signs, handrails and stair nosings, retail displays, gym and garage accent lines, and architectural outlines on facades. Contractors finishing a basement bar, a sign shop building custom lettering, or a homeowner running neon around a home theatre all end up needing the same thing: a clean terminated edge that matches the profile in hand.

Compatible accessories
Build your run with the matching family: the flex neon endcap side view without hole for side-emitting profiles, the flex neon endcap 3x6 without hole and flex neon endcap 6x6 without hole for those squared profiles, plus the drilled versions such as the flex neon endcap 6x6 with hole when the cable has to pass through at the feed end. SKU LCENDCAP-FLX-TV-NH ships as the cap only — silicone adhesive or sealant is supplied separately. No spec sheet or IES file is published for this accessory; select it by measuring your existing top-view profile.