FLEX NEON ENDCAP 3X6 - (WITH HOLE)

Name: FLEX NEON ENDCAP 3X6 - (WITH HOLE)
Brand: LEDCO
SKU: LCENDCAP-FLX-3X6-H
Price: 3.97 CAD
Availability: InStock

SKU: LCENDCAP-FLX-3X6-H

Brand: LEDCO

Every neon flex run has to end somewhere — and that raw, open face is what separates a clean sign from an amateur job. This flex neon endcap 3X6 with hole is the small part that finishes the job right: it closes the cut end of your LED neon flex profile while letting the supply wire or connector exit through the centre hole. Whether you call it an end cap, a finishing cap, a neon flex plug or simply an embout, it is the piece that turns a cut length of LED neon rope light into a finished, sealed fixture. Sold as a single unit, so you order exactly the count your project needs — one capped feed end per run, plus a spare or two for future trims.

Designed to match the profile dimensions of the 3X6 neon flex it is made for, this cap seats snugly so the silhouette stays uniform from one end of the run to the other — no bulge, no gap, no light leak at the termination. The version with hole is the wire-exit cap: it lets the power lead or connector pass through cleanly instead of forcing you to notch or improvise. Installed with the recommended adhesive or sealant, it supports a properly sealed termination, which is what allows a run to be used in damp or wet locations where the flex itself carries that rating, and what keeps dust, sawdust and grease out of the end of the strip. SKU LCENDCAP-FLX-3X6-H.

This is the cap reachable for anyone building LED neon signs, cove lighting, under-counter accents, stair nosings, storefront outlines, garage and workshop lighting, or backlit logos for a small business. Canadian shops, restaurants, barbershops, gyms and home theatres all run into the same issue: the flex gets cut to length on site, and the ends need to be finished before power goes on. Use this one at the feed end, and pair it with the Flex neon endcap 3X6 (without hole) to close the far end of the same run. Working with a larger profile? The Flex neon endcap 6X6 (with hole) and the Flex neon endcap 6X6 (without hole) cover that size. Grab a few and finish your run properly.

Compatible with
Works with:
LED strip: LCLS24VFLX-3X6-9.6W-27K, LCLS24VFLX-3X6-9.6W-27K-30M, LCLS24VFLX-3X6-9.6W-30K, LCLS24VFLX-3X6-9.6W-40K, LCLS24VFLX-3X6-9.6W-40K-30M

What this endcap is and what it solves
Neon flex is meant to be cut to length. That is its biggest advantage — and the reason every installation ends with an exposed, open face where the silicone or PVC body was sliced. Left as is, that face invites dust, moisture and damage, and it looks unfinished. This flex neon end cap with hole closes that face while giving the supply wire or the connector a clean route out of the profile. It is the feed-end counterpart to a solid, no-hole cap: one hole cap where the power enters, one blank cap where the run terminates.

Fit and construction
The cap is made to pair with standard neon flex profiles in the 3X6 format, so the opening matches the body of the flex and the cap sits flush rather than perched on the end. That snug fit matters for two reasons: visually, the run keeps the same continuous line right to the tip, and mechanically, the cap holds adhesive in a thin, even layer instead of squeezing out into a mess. Several sizes and configurations exist across the accessory range — top view, side view, with and without hole — so you can match caps, mounting clips and connectors to the exact profile you are working with.

Technical specifications
SKU: LCENDCAP-FLX-3X6-H
Type: Finishing end cap for LED neon flex
Profile format: 3X6
Configuration: With hole (wire / connector exit)
Quantity: 1 unit
Category: End caps, lenses and accessories

Installation, sealing and electrical routing
Cut the flex only at the marked cut points — cutting elsewhere breaks the LED circuit inside. Wipe the end clean and let it dry completely before capping; silicone will not bond to a dusty or damp face. Feed the supply wire or connector through the hole, apply a thin, even bead of the recommended adhesive or sealant inside the cap and on the flex face, seat the cap fully, then wipe the excess. Let it cure completely before powering up or exposing the run to moisture. That cure step is what creates the sealed termination that makes a run suitable for damp or wet-location use where the flex itself is rated for it, and what keeps debris out of installations in shops, kitchens and workshops. Keep a spare cap or two on hand for future trims and repairs.

Where it gets used and what pairs with it
Think custom LED neon sign lettering in a café or tattoo studio, cove and ceiling perimeters in a condo living room, toe-kick and under-cabinet accents in a kitchen, stair and handrail lighting, storefront and window outlines, garage and workshop strips, and event or showroom displays. For the closed end of the same 3X6 run, use the Flex neon endcap 3X6 (without hole). Larger profiles are covered by the Flex neon endcap 6X6 (with hole), and side-emitting or top-emitting builds by the Flex neon endcap side view (without hole) and the Flex neon endcap top view (without hole). No documents are listed for this accessory; match the cap to your flex profile format before ordering, and buy one per cut end.