FINISHING END CAP #91 (WITH HOLE) – 1 UNIT

Name: FINISHING END CAP #91 (WITH HOLE) – 1 UNIT
Brand: LEDCO
SKU: LCENDCAP-STAND-91-H
Price: 5.97 CAD
Availability: InStock

SKU: LCENDCAP-STAND-91-H

Brand: LEDCO

Give your LED channel a clean, finished look right to the very edge. This finishing end cap #91 with hole is the small part that makes a big difference: it closes off the open end of an LED aluminum profile while leaving a dedicated opening for the supply wire to exit. People search for it as an LED channel end cap, an LED strip light end cap, a profile cap or simply a plug for aluminum extrusion — same piece, same job. Sold as 1 unit (SKU LCENDCAP-STAND-91-H), it is the companion to the solid, no-hole version that seals the opposite end of the same channel. Put the two together and a bare cut extrusion suddenly looks like a real, purpose-built linear fixture instead of an open aluminum tube with wires hanging out.

The design is straightforward and that is exactly why it works. The cap matches the #91 standard profile shape, with a pre-made wire exit hole so your low-voltage lead can pass through without pinching, kinking or being visible at the end of the run. It friction-fits into the extrusion for a snug, gap-free closure; a small dab of adhesive adds extra holding power for overhead runs or high-traffic areas where a cap could get bumped loose. Because end caps are profile-specific, always compare the shape and dimensions of your channel with the cap before ordering — surface mount, recessed, corner and suspended extrusions each take their own style. If your channel has been cut to a custom length, deburr the cut edge first so the cap seats flush and square against the aluminum.

This #91 end cap with hole earns its keep everywhere LED strip is installed in a channel: under-cabinet lighting in a kitchen, cove and ceiling details in a living room, display cases and shelving in a retail boutique, backlit signage, garage and workshop task lighting. It fits residential renovations and light-commercial projects across Canada equally well. Pair it with the matching solid cap on the far end, and if you are also running flexible neon elsewhere in the project, look at the Flex Neon endcap 6x6 with hole or the Flex Neon endcap 3x6 with hole. Order the pair you need and finish the job properly.

Compatible with
Works with:
Channel / profile: LCPROF-91-10FT

What this end cap actually does
An aluminum LED profile leaves two open ends once it is cut to length, and those openings are where a good installation starts to look unfinished: exposed strip, visible solder points, dust and a loose power lead. This finishing end cap with hole closes one of those ends and gives the supply wire a clean, dedicated exit. The other end gets the solid cap, with no hole, so nothing is left open. The result is a complete linear fixture built from parts — the same look you get from a sealed factory-made fixture, but with the freedom to cut your LED channel to whatever length the cabinet, cove or shelf demands.

Fit and compatibility
This is the #91 standard profile cap, and end caps are profile-specific: every extrusion shape has its own matching cap. Before you order, hold the cap profile against the end of your channel and confirm the shape and dimensions line up for a snug, gap-free fit. Surface mount, recessed, corner and suspended extrusions all use different cap shapes, so the safest habit is to match the cap to the channel model you are buying, not to a similar-looking one you already have in the shop. Each cap is sold individually, which lets you order exactly what a run needs: one with a hole at the feed end, one without a hole at the far end, and a couple of spares for the job box.

Installation tips that save a callback
Feed the low-voltage wire through the hole before pressing the cap into place, and leave a little slack inside the channel so the solder joint or connector is never under tension — tension at the strip's pad is one of the most common causes of a dead section months later. If the channel has been cut on site, file or deburr the aluminum edge so the cap seats flush and square; a burr is usually why a cap sits proud or pops off. The cap normally friction-fits, but for overhead cove work, garage ceilings or anywhere people brush past the fixture, a small dab of adhesive keeps it in place permanently. Do a quick power-up test before you close everything in.

Where it shines
Think under-cabinet and over-cabinet kitchen lighting, bathroom vanity strips, cove and ceiling perimeter details, staircase and hallway accents, closet and pantry shelving, retail display cases, bar and restaurant millwork, backlit signage, and workshop or garage task lighting. Contractors appreciate that a finished channel with proper caps looks deliberate and holds up to cleaning, while homeowners simply notice that the light looks built-in. In Canadian renovations where millwork runs are rarely a standard length, the cut-to-fit channel plus matching caps combination is the practical way to get a custom look.

Product and related pieces
SKU: LCENDCAP-STAND-91-H
Type: Finishing end cap, standard profile #91, with wire exit hole
Quantity: 1 unit
Category: End Caps, Lenses & Acc.
For other profile shapes in the same family, see the finishing end cap #11 with hole and the finishing end cap #11 without hole. For flexible neon projects, the Flex Neon endcap side view covers side-emitting runs. No spec sheet or IES file is published for this accessory; select it by matching the profile shape of your channel.