FINISHING END CAP #86 (NO HOLE) – 1 UNIT

Name: FINISHING END CAP #86 (NO HOLE) – 1 UNIT
Brand: LEDCO
SKU: LCENDCAP-STAND-86
Price: 3.97 CAD
Availability: InStock

SKU: LCENDCAP-STAND-86

Brand: LEDCO

Every clean-looking LED channel run ends with one small detail — and this is it. The FINISHING END CAP #86 (NO HOLE) is the solid trim piece that closes the extremity of an aluminum LED channel, sold as 1 unit so you order exactly what your job needs. People look for it as an LED channel end cap, an LED strip light end cap, a profile end plug or simply a channel cap, and it does a job no other part can do: it squares off the open end of an extrusion so the finished run looks intentional instead of unfinished. This is the no-hole version, meant for the closed end of a run where no power lead or connector has to exit.

Because it is a physical trim part, its value is in the fit and the finish. End caps are profile-specific, so this one is matched to the #86 channel family — order the cap that belongs to the extrusion you are installing, and it seats flush against the profile walls with no gaps and no daylight showing through. Once in place, it shields the LED strip and the diffuser end from knocks, dust, insects and stray debris, which matters a lot in kitchens, workshops and retail displays. Caps are typically offered in finishes that blend with the extrusion, and since it ships as a single unit you can buy one for a closed end, two for a run fed from a remote driver, or a handful for a multi-run millwork project. SKU LCENDCAP-STAND-86.

This little part shows up everywhere: under-cabinet lighting, cove and ceiling details, stair nosings, closet and pantry shelving, display cases, reception desks and light-commercial millwork in Canadian homes, shops and offices. Use the no-hole cap on the dead end of the channel, and keep the version with a cable opening for the feed end so the power wire passes through without pinching — the same logic applies to the Finishing end cap #11 (no hole) and Finishing end cap #11 (with hole) on their own profile. Add a pair to your channel order and finish the run properly the first time.

Compatible with
Works with:
Channel / profile: LCPROF-86-16FT, LCPROF-86-16FT-LENS-OPAQ, LCPROF-86-8FT, LCPROF-86-8FT-LENS-OPAQ

What this end cap is
An end cap is the small trim piece that closes the extremity of an aluminum LED channel. Without one, you see the raw cut of the extrusion, the end of the diffuser and, worse, the end of the LED tape itself. This model is the solid, no-hole style: there is no cable opening, so it is used at the closed end of a run where no power lead, jumper or connector needs to exit the profile. It is sold as 1 unit, which keeps ordering simple whether you need a single cap for one closed end or several for a long millwork package.

Fit and compatibility
End caps are profile-specific — the shape of the cap has to match the exact cross-section of the extrusion, including its wings, channels and diffuser groove. This one belongs to the #86 profile family, so match the cap to the channel family you are installing rather than to a generic size. Several profile styles and matching accessories are available across the range, including the standard series like the Finishing end cap #11 (no hole), and dedicated caps for flexible neon such as the Flex neon endcap 3x6 (without hole) and the Flex neon endcap 6x6 (without hole). If you are unsure, compare the cap silhouette to the end view of your extrusion before cutting anything.

Technical specifications
SKU: LCENDCAP-STAND-86
Product: Finishing end cap #86, no hole
Type: Solid end cap, no cable opening
Quantity: 1 unit
Profile family: #86 standard channel
Category: End caps, lenses and accessories

Installation
Work in order and the finish takes care of itself. Cut the channel to length and clean the cut so there are no burrs or aluminum shavings left inside, then install the LED strip and the diffuser, and finally press the cap into the open end. Friction usually holds it, but in high-traffic or overhead locations — stair nosings, under-cabinet edges, a retail counter people brush against — a small dab of adhesive or a fastener keeps it from working loose over time. At the powered end of the run, use the matching version with a cable opening so the power lead passes through without being pinched between the cap and the extrusion; a pinched conductor is a service call waiting to happen. Do the same at any point where you exit the profile to jump to the next section.

Where it is used
Under-cabinet and over-cabinet LED strip lighting, cove and ceiling details, stair nosings, shelving, closets and pantries, display cases, bar fronts, reception desks and light-commercial millwork — anywhere a linear LED run needs a tidy, durable finish in Canadian homes and businesses. Contractors often add a couple of extra caps to the order: they are the first thing to disappear on a busy site and the last thing you want to be missing when the client walks through. No documents are listed for this accessory; for channel dimensions and diffuser options, refer to the documentation of the #86 profile you are pairing it with.