10 FEET 45 DEGREE ALUMINUM PROFILE FOR LED STRIP (LUX2400)

Name: 10 FEET 45 DEGREE ALUMINUM PROFILE FOR LED STRIP (LUX2400)
Brand: LED MONTREAL
SKU: 10FLUX2400
Price: 76.97 CAD
Availability: InStock

SKU: 10FLUX2400

Brand: LED MONTREAL

Turn a bare strip of light into a crisp, finished corner detail. This is the 10 feet 45 degree aluminum profile for LED strip (LUX2400) from LED MONTREAL, the corner-mount aluminum extrusion installers reach for when they want led strip lighting to look built-in instead of stuck on. People search for it as an LED channel, a corner track, an extruded aluminum housing or simply a profile for led strip lights — it is all the same idea: a rigid aluminum body that holds your tape, hides the diodes and gives the whole run a clean, professional line. It sits in the 45° angle where a ceiling meets a wall, under a cabinet, along a stair stringer or on the top of a bookcase, and it aims the light out into the room instead of straight down.

The angled design is the whole point. The 45 degree cut spreads the beam over a wider radius for softer, more even light with fewer hot spots, and the aluminum body pulls heat away from the tape so your diodes keep their brightness longer. Model 10FLUX2400 is a surface-mount 45° profile measuring 10 feet (3.05 m) long, 20 mm wide and 20 mm high — a compact square section that disappears into most corners. It accepts an IP20, an IP65+ or certain IP67 LED strips, so you can use the same look indoors and in damp spots. Note that this 10-foot model has been discontinued and is offered in black only, while supplies last; for the anodized aluminum finish, the 8-foot version is the way to go. Because of its length, this profile is available at our service counter only — it cannot be shipped by mail.

It shines in kitchens over the upper cabinets, in basements and home theatres for indirect cove lighting, along hallways and staircases, and in shops, restaurants, offices and display cases where a continuous line of light sets the mood. A single 10-foot piece means fewer joints on long Canadian basement walls or storefront perimeters. Hold it in place with optional aluminum clips or with our sturdy double-sided tape, then finish the run with matching end caps for that polished touch. Need the anodized look or a shorter piece that ships? Go with the 8 feet 45 degree aluminum profile for LED strip (LUX2400). Grab yours at the counter while the black stock lasts.

Built to make your strip look installed, not improvised
The LUX2400 family is a 45° corner aluminum profile, and this is the long version: a one-piece 10-foot extrusion in a tidy 20 mm x 20 mm square section. Set it into an inside corner and the angled face points your led strip lighting out at 45 degrees, exactly where you want the light to travel. Aluminum is the material of choice here for two reasons: it is rigid enough to keep a perfectly straight line over a long run, and it acts as a heat sink, drawing warmth away from the LED tape. Cooler tape means steadier output and a longer service life from the strip you install inside it. This 10-foot model has been discontinued and remains available in black only while supplies last.

Technical specifications
Model: 10FLUX2400
Type: 45° (Surface)
Length: 10 Feet (3.05 m)
Width: 20 mm
Height: 20 mm
Brand: LED MONTREAL
Availability: service counter only — cannot be shipped by mail because of its size

Light quality and strip compatibility
A bare tape shows every diode; a profile blends them. The 45° geometry of this aluminum extrusion widens the throw so the light washes a wall or a countertop rather than punching a single hard stripe. It accepts an IP20 strip for dry interiors, an IP65+ strip for kitchens, bathrooms and sheltered areas, and certain IP67 strips as well — check that the silicone jacket of your tape fits the 20 mm channel before cutting. Choose the colour temperature and output of your tape according to the job: warm tones for living rooms and restaurants, neutral or cool tones for workshops, garages and retail displays. The profile itself does not limit voltage or wattage, so it works the same with low-voltage tape runs as with longer feeds.

Installation, mounting and finishing
Plan the run first, then cut the extruded aluminum to length with a fine-tooth blade or a mitre saw, deburr the edges, and dry-fit before sticking anything. Two mounting methods are common: optional aluminum clips screwed into the corner, which let you snap the profile on and off later for service, or our sturdy double-sided tape for a fast, screw-free job on clean, dry surfaces. Feed the strip in, keep the solder joints and the power lead outside the channel where possible, and cap both ends with matching end caps so dust stays out and the ends look deliberate. In a 45° corner, aim the open face away from sightlines so people see the glow, not the diodes.

Where it earns its keep, and what to pair it with
Think cove lighting above kitchen cabinets, indirect ceiling perimeters in a basement family room, under-counter light in a bar or reception desk, shelf and display case lighting in a boutique, and stair or corridor lighting in a condo building. Contractors like the 10-foot length because long walls need fewer joints and fewer visible seams. Since this length is counter pickup only and black only, many projects pair it with the 8 feet 45 degree aluminum profile for LED strip (LUX2400), which is also offered in anodized aluminum for a lighter, brushed look. The technical PDF for SKU 10FLUX2400 is available in the Documentation tab with the full dimensions if you need them for your shop drawings.

Technical Files