L-SHAPE COB CONNECTOR WITH WIRE CABLE 2-PIN 8MM FOR LED STRIP

Name: L-SHAPE COB CONNECTOR WITH WIRE CABLE 2-PIN 8MM FOR LED STRIP
Brand: LEDCO
SKU: LCCON-CLIPCOB-LWIRE-8MM
Price: 2.97 CAD
Availability: InStock

SKU: LCCON-CLIPCOB-LWIRE-8MM

Brand: LEDCO

Turning a corner with LED strip lighting should never mean a soldering iron, a burnt fingertip and a kinked tape. This L-shape COB connector with wire cable, 2-pin, 8MM — also called an L connector, corner connector, right-angle jumper or simply a solderless LED strip connector — joins two runs of two-pin single-colour COB LED tape at a right angle using a short flexible lead. Instead of forcing the strip to fold around a cabinet return, a cove or a door frame, you cut on the marked line, clip both ends and let the cable do the bending. It is the little part that makes strip lights look like they were planned by a designer instead of improvised on site.

Built for 8MM two-pin COB LED strip, this connector uses clamp-style contacts that grip the copper pads of the tape directly, so you get a reliable electrical path without solder, flux or specialty tools. The two-pin format keeps polarity consistent from one section to the next, which means even brightness and no flicker along the run — the seamless, dot-free look COB tape is known for stays intact right through the corner. The body is low-profile, so it tucks into aluminum channel or behind trim, and the connection stays dimmable with the dimmers and drivers already on your circuit. The flexible lead lets you route around mouldings and obstacles instead of fighting them.

Under-cabinet lighting, cove and ceiling details, stair nosings, closets, signage, display cases, garage workbenches — anywhere a run of ruban LED has to change direction, SKU LCCON-CLIPCOB-LWIRE-8MM earns its place in the toolbox. Canadian renovators, cabinetmakers and shop owners keep a handful on hand because corners never show up where you planned them. For tight corners with no gap to cross, use the L-shape COB connector 2-pin 8mm, and to rejoin two straight sections in line, the straight COB connector 2-pin 8mm. Add a few to your next LED strip lights order and finish the job in one trip.

Built for clean, solderless corners
This connector is a corner solution for two-pin single-colour COB LED strip in the 8MM width. The clamp-style contacts close over the copper pads on the tape and hold them against the internal terminals, creating a mechanical and electrical connection in seconds. Between the two clips sits a short flexible cable, and that cable is the whole point: it lets the light turn a corner while the tape itself stays flat and unstressed. Bending COB tape sideways stretches the copper traces and is a classic cause of dead sections weeks after installation — a wired L connector removes that risk completely.

Light quality through the joint
COB tape is prized for its continuous, dot-free line of light, and a bad joint ruins that in one spot. Because this is a two-pin connector, polarity is carried straight through, so both sections stay at the same brightness with no flicker and no colour shift at the transition. The connection behaves exactly like the rest of the circuit: if your strip and driver are dimmable, the run stays dimmable through the connector. Keeping the contacts clean and fully seated is what protects that uniformity over time.

Installation, step by step
Always cut the strip on the marked cut line, never between the marks. Wipe the copper pads clean — dust, adhesive residue or fingerprints are the most common cause of a weak contact. Open the clip, slide the tape fully under the contacts until the pads sit squarely on the terminals, then close the clip firmly. Confirm that the positive and negative markings line up on both sides before powering up, and test the whole run before you mount the aluminum channel or peel the adhesive backing. The low-profile body is designed to disappear inside a channel or behind trim, so plan where the joint will land while the strip is still loose.

Technical specifications
SKU: LCCON-CLIPCOB-LWIRE-8MM
Type: L-shape corner connector with wire cable
Contacts: 2-pin, single-colour
Strip width: 8MM
Strip type: COB LED strip
Connection: solderless clamp-style contacts
Dimming: dimmable with compatible dimmers and drivers

Applications and companion parts
Think of every place a run has to change direction: an L-shaped kitchen counter, a cove that wraps a living-room ceiling, stair nosings, a closet returning along two walls, illuminated signage, retail display cases and workbenches. It is a practical accessory for residential and light-commercial LED strip lighting projects across Canada, where basement renovations and cabinet installs rarely run in a single straight line. Pair it with the L-shape COB connector 2-pin 8mm for corners with no gap, the straight COB connector 2-pin 8mm for in-line joints, and the green connector for power supply or green female connector for power supply at the driver end of the circuit. No spec sheet or IES file is published for this accessory; the details above cover what you need to order the right part the first time.