Built as one solid pieceThe RGD-CDR/HO housing is a single-piece body — nothing to disassemble, nothing to rattle loose above a suspended ceiling. The LED source sits regressed behind the lens, which pushes the bright spot up into the fixture and keeps direct glare out of the eyes of people working at desks, standing at a counter or looking up in a corridor. The white trim reads as a clean circle in painted drywall or a T-bar tile, and integrated spring arms clamp onto the upper surface of the ceiling panel so the fixture pulls itself tight without screws or clips.
Light you choose at the ceilingTwo slide switches on the back of the housing do the work that used to require four different order codes. The CCT select switch moves between 2700K (soft white), 3000K (warm white), 3500K (neutral white), 4000K (cool white) and 5000K (daylight) — five selectable colour temperatures, so a designer can warm up a lobby and cool down a back office with identical stock. The wattage select switch, marked right beside it, sets 13W, 15W, 18W or 23W, delivering 1300, 1500, 1800 or 2300 lumens. Ceiling too bright after drywall and paint? Drop a step instead of swapping fixtures.
Wiring, dimming and installationUniversal
120-347V input covers residential, light commercial and 347V commercial services with one part number. The unit supports either
TRIAC dimming or 0-10V DC dimming: for phase control, check the dimmer compatibility list; for 0-10V, connect the purple and pink wires to the matching purple and pink control wires of the building dimming system, and simply leave them unconnected if no dimming is required. Line wiring is black to black, white to white and green to green/bare — and if there is no ground supply wire, stop and call a qualified electrician. The kit includes the downlight, an input power conduit lead, a
safety cable to anchor above the plenum and five wire nuts. Estimated assembly time is 5 minutes and no tools are required for assembly. The fixture needs a minimum lamp compartment of 5.51 in. diameter x 7.4 in. height, is intended for indoor use only, and is not for emergency fixtures, exit signs or locations exposed directly to weather or water.
Technical specificationsSKU: RGD-CDR/HO/6/MW/MK9/120-347V/WH/D
Brand: TUROLIGHT
Aperture: 6 in. regressed commercial downlight
Selectable wattage: 13W, 15W, 18W, 23W
Lumen output: 1300 / 1500 / 1800 / 2300 lm
Colour temperature: 5 selectable CCT — 2700K, 3000K, 3500K, 4000K, 5000K
Voltage: 120-347V
Dimming: compatible TRIAC dimmer or 0-10V DC system
Finish: white
Minimum lamp compartment: 5.51 in. (diam.) x 7.4 in. (H)
Use: indoor only
Included: downlight, input power conduit lead, safety cable, 5 wire nuts
Where it works and what to pair it withThink open offices and meeting rooms on 0-10V controls, retail aisles that need punch at 23W near entrances and a softer 13W over fitting rooms, clinic corridors at 3500K, restaurant ceilings at 2700K, condo lobbies, schools, warehouse offices and basement renovations. Because the aperture family shares the same switches and white trim, you can mix sizes in one ceiling grid: the
Rigid 4" regressed downlight for tight spots, the
Rigid 8" regressed downlight and the
Rigid 10" regressed downlight for high or wide ceilings. For general ambient fill in the same T-bar ceiling, TUROLIGHT
2x4 LED panels in 120-347V share the same voltage range.
Care and documentationClean with a mild, non-abrasive glass cleaner and a soft cloth, power off, spraying the cloth and never the fixture; avoid solvents and abrasive cleaners. The full spec sheet and installation instructions for RGD-CDR/HO/6/MW/MK9/120-347V/WH/D are in the Documentation tab — worth printing for the electrician before the ceiling closes up.
