PHANTOM MOUNTING BRACKET #81 (EACH)

Name: PHANTOM MOUNTING BRACKET #81 (EACH)
Brand: LEDCO
SKU: LCBRACK-STAND-81
Price: 2.97 CAD
Availability: InStock

SKU: LCBRACK-STAND-81

Brand: LEDCO

Every clean LED strip installation comes down to one small part doing its job perfectly: the bracket that holds the channel exactly where you want it. The PHANTOM MOUNTING BRACKET #81 is that part — a dedicated installation bracket (also called a light mounting bracket, mounting clip or support bracket) made to secure the Phantom #81 aluminum extrusion to the surface of your choice. Sold by the unit under SKU LCBRACK-STAND-81, it lets you place your supports exactly where the run needs them instead of settling for whatever spacing a kit decides for you.

This is a purpose-built accessory, not a universal clamp, and that's exactly why it works so well: it matches the profile of the #81 series, so the channel seats firmly, sits straight and stays straight — no sagging mid-run, no twisted diffuser, no light lines that wander off the ceiling edge. Because it's sold individually, you can buy the exact count your project calls for, keep a few spares in the van, and add extra LED strip channel supports at joints, corners and over longer unsupported spans where the profile needs a little more help. Mount it first, snap or slide the profile in, and your LED strip light bracket does the holding while you focus on the wiring and the diffuser.

It's a favourite for residential and commercial work alike: under-cabinet lighting in a kitchen renovation, cove and ceiling perimeter runs in a living room, closet and pantry strips, garage and workshop task lighting, retail shelving, display cases, reception desks and office millwork. Contractors across Canada rely on these small mounting brackets to keep long runs tidy on drywall, plywood, cabinet boxes and metal surfaces alike. Use it only with the Phantom #81 profile family; for other extrusions, see the matching supports such as the Mounting bracket #80, the Standard installation bracket - series #84 or the Standard installation bracket - series #10. Count your supports, order what you need and get that strip up straight the first time.

Compatible with
Works with:
Channel / profile: LCPROF-81-16FT, LCPROF-81-8FT

Built for one job, done right
The PHANTOM MOUNTING BRACKET #81 is a single-piece mounting bracket designed specifically for the Phantom #81 aluminum profile. Unlike improvised straps or generic clips, its shape follows the extrusion, so the channel is gripped along its own mounting geometry rather than squeezed out of shape. That means a flat, continuous line of light instead of a profile that bows between two distant screws. Each bracket is sold individually (SKU LCBRACK-STAND-81), which makes it easy to match the support count to the real length of your run and to keep replacements on hand for service calls.

Why bracket spacing matters
An LED strip channel is only as straight as the supports behind it. Too few brackets and the extrusion dips in the middle, the diffuser shows waves, and the light line looks uneven on a ceiling or under a cabinet. Adding a bracket near each end of the profile, on either side of a joint between two lengths, and at regular intervals in between gives you a rigid, quiet installation that will not shift when someone bumps a shelf or when the room heats up and cools down. Corners, transitions and any spot where two runs meet always deserve an extra installation bracket.

Installation tips
Work in this order: mark your line with a laser or chalk, fasten the brackets to the surface, then engage the profile. Choose fasteners suited to the substrate — wood screws into cabinet boxes, studs or blocking; anchors in drywall; self-tapping screws in metal framing or T-bar and suspended ceiling structures. Always check for wiring before drilling, keep the driver location accessible, and leave your channel ends free so the end caps and the diffuser can slide into place. A dry fit of the full run before the final tightening saves a lot of re-drilling. These are light mounting brackets for the mechanical side of the job only — all electrical connections must follow the Canadian Electrical Code and local requirements.

Where it gets used
Kitchen under-cabinet and toe-kick lighting, cove lighting around a living room ceiling, stairwell and hallway accents, walk-in closets, home theatres, basement renovations and garage workbenches on the residential side. On the commercial side: retail shelving and display cases, bakery and deli counters, salon mirrors and stations, reception desks, hotel corridors, office millwork and cabinetry in clinics. Anywhere a linear LED strip profile needs to be held straight and square, this bracket earns its keep.

Compatibility and matching supports
Use this bracket with the Phantom #81 profile series only — a bracket from another series will not hold the extrusion correctly. If your project mixes profiles, pick the matching support for each one: Standard installation bracket - series #84 #85 #86, Swivel installation bracket - series #85 for adjustable-angle runs, Installation bracket - series #4064 or Installation bracket - series #9400. No spec sheet or documentation file is published for this accessory; if you are unsure which series your extrusion belongs to, compare the profile shape with the bracket before ordering your quantities.