MOUNTING BRACKET #80 (EACH)

Name: MOUNTING BRACKET #80 (EACH)
Brand: LEDCO
SKU: LCBRACK-STAND-80
Price: 2.97 CAD
Availability: InStock

SKU: LCBRACK-STAND-80

Brand: LEDCO

Small part, big difference: the MOUNTING BRACKET #80 (EACH) is the little piece of hardware that turns a length of LED profile into a clean, solid, finished installation. People look for it under a lot of names — installation bracket, light mounting bracket, light bracket, LED channel clip, aluminum extrusion holder — but the job is always the same: hold the profile exactly where you want it, straight and tight, so the light line looks intentional instead of improvised. This bracket is designed for the #80 series profile and is sold per unit, so you order only the quantity your run actually needs, whether that's two for a short accent strip over a kitchen island or a dozen for a long corridor cove.

Because it's a dedicated LED strip mounting bracket, it does its work out of sight. You fasten the bracket to the surface first, then snap or slide the profile into place, which means no fighting with adhesive tape that lets go six months later and no screw heads drilled through the face of your extrusion. The result is a channel that stays perfectly aligned, sits flush and can be removed later for service — handy when a driver or a section of tape light eventually needs attention. Since it's sold individually, spacing is up to you: add more brackets on long spans, on ceilings, or anywhere the profile needs extra support.

This is a favourite of contractors and renovators across Canada for surface-mounted LED profile work: under-cabinet lighting, closets and pantries, stair nosings, garage and workshop benches, retail shelving, reception desks, display cases and hallway cove details — residential and commercial alike. It belongs in the same toolbox as the rest of the family, including the Phantom mounting bracket #81, the standard installation bracket series #84 and the standard installation bracket series #10, each matched to its own profile. Order SKU LCBRACK-STAND-80 by the unit, keep a few spares on the truck, and give every LED strip run the support it deserves.

Compatible with
Works with:
Channel / profile: LCPROF-80-16FT, LCPROF-80-8FT

What it is and what it does
The MOUNTING BRACKET #80 is an installation accessory for LED strip systems — the mechanical link between your mounting surface and the #80 series aluminum profile. It ships as a single piece (each), which is exactly how installers want to buy it: one bracket at a time, in the count the job calls for. In practice it replaces double-sided tape and improvised screws with a repeatable method, so every profile in a project is held the same way, at the same height, in the same line.

Installation, step by step
The sequence is simple. Mark your line, position the brackets along the run, fasten them to the substrate with the appropriate anchors for that surface (wood, drywall with anchors, metal stud, cabinet carcass), then engage the profile into the brackets and check the alignment end to end. Because the profile clips into the LED channel bracket rather than being drilled through, the face of the extrusion stays clean and the diffuser can still be slid in and out. More brackets means less sag: add them wherever the run is long, overhead, or under vibration such as in a garage or a workshop. And because it's a mechanical hold, the profile can be taken down later for maintenance and put right back.

Where it earns its keep
Think under-cabinet lighting in a kitchen, a lit toe-kick, closet and pantry shelving, a basement stair with a light line under the nosing, a home office desk, or a workbench that finally gets shadow-free task light. On the commercial side: retail shelving and display cases, a reception desk front, a cove detail in a corridor, a restaurant bar, a clinic waiting room. In Canadian homes and businesses where LED tape has replaced fluorescent strip light, a proper installation bracket is what keeps the result looking built-in instead of stuck-on years down the road.

Compatibility and matching parts
This bracket is made for the #80 series profile — always match the bracket to the profile series, since each extrusion shape has its own hold. If your project mixes profiles, the same family covers them: the Phantom mounting bracket #81, the standard installation bracket series #84 #85 #86, the swivel installation bracket series #85 when the profile needs to be aimed, and the installation bracket series #9400. A quick count before you order saves a second trip: one bracket near each end, plus intermediates along the span.

Ordering and documentation
Order by SKU LCBRACK-STAND-80, sold each, and add the quantity your run requires. No datasheet or IES file applies to a mechanical accessory like this one, so the important detail is simply the series match: #80 profile, #80 bracket. Buy a few extras — brackets are the part everyone underestimates on site, and having them on hand keeps an LED strip installation moving.